The Vision Eternity Rebuildable Atomizer (RBA) Designed by Vision and Made by LG
510 Threaded

This atomizer can be completely disassembled and reassembled. The atomizer coil is replaceable like with other rebuildable atomizers, but features a screw-less wick/coil assembly for quicker installation and replacement of a new coil and wick.

Replacement Wicks and Coils for this product can be purchased here:  Vision Eternity Replacement Coils and Wicks 5pk

***Due to the highly advanced nature of this product, technical support is not available for this product.  If you are not comfortable in your ability to operate this device please do not purchase it as refunds will only be allowed for defective units.  Units that are damaged due to misuse will not be replaced.

To change the wick/coil:

1. Disassemble the atomizer completely
2. Carefully wrap the coil around the center of the wick several times in a tight spiral pattern leaving plenty of extra coil at each end
3. Thread the ends of the coil through the post caps
4. Push the post caps up the coil until they reach the wick and then bend the coil at the bottom of the post cap to hold them in place
5. Snap the post caps onto the posts of the Eternity atomizer base.
6. Test with a meter to ensure it is reading your preferred resistance (to readjust the resistance you must recoil the wire to leave more wire (higher resistance) or less wire (lower resistance) between the pole caps).
7. Trim the excess wire just below the pole caps
8. Reassemble the atomizer
9. Fill with liquid and you are ready to vape

The Vision Eternity RBA can be used as a drip atomizer holding up to 40 drops of E-liquid or as a tank-style atomizer with an eGo-T/eGo-C Type A cartridge and soft end cap. Improvements over the standard eGo-T/eGo-C atomizer spike have been incorporated in the design of the Eternity atomizer spike. This new spike requires a larger hole in an Ego-T/Ego-C Cartridge which makes it incompatible with the hard cap version of the cartridge. The Eternity Atomizer kit includes all the necessary parts to convert between dripping and tank-style. 

Vision has worked long and hard to make the ULTIMATE Rebuildable Atomizer! Both in design, packaging, testing and development in a high quality-assured environment. The quality and beauty you see in the product and packaging reflects the dedication VISION has had towards this product.

The Vision Eternity is made of quality, highly polished chrome plated pure brass and included in your 6 piece set up is a beautiful ribbed eGo sleeve cover you can use optionally at the base that threads onto your outside Ego threads. 

Contents:
1 x 510 threaded base (holds the coil and wick)
1 x eGo threading trim ring
1 x Spike assembly
1 x dripping cone (used with 510 drip tip)
1 x tank cartridge cone (used with eGo-T/eGo-C Type A Cartridge)
1 x 510 chrome driptip
1 x pre-installed wick/coil assembly
2 x silicone ego-t type A soft end caps (cartridges must be purchased separately)
2 x wick/coil assemblies
1 x extra set of post caps for the coil/wick assembly

All packaged in a nice tin with instruction manual.


Important Note:

Rebuildable atomizer coils and wicks have known risks.

Rebuildables are for experts, not average or beginner vapers with no multimeter or knowledge of how to use a meter, or when a meter must be used, or how electronic devices work. These materials cannot safely be used by the inexperienced or those without basic knowledge of electronics.

This is because:

1. A rebuildable coil/wick MUST be tested carefully with a meter before it is used.
2. If it is not tested it is entirely the risk of the user.
3. Faulty wicks/coils WILL blow electronic devices.
4. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protection.
5. No new coil/wick assembly should be used on an electronic device until known to be safe.
6. These items destroy electronic devices if faulty. This is a known issue.